Guillows Arrow RC CONVERSION

Ask other modelers for a little help / knowledge ?

Guillows Arrow RC CONVERSION

Postby jonathanmanopla » Fri Jul 12, 2013 11:18 am

SOMEONE USE ALREDY EZE DOPE , IT WORKS OK?

IM STARTING COVERING A GUILLOWS ARROW LC

AND I WANT TO TRIED
Last edited by jonathanmanopla on Mon Sep 23, 2013 11:11 am, edited 2 times in total.
jonathanmanopla
 
Posts: 23
Joined: Fri Feb 08, 2013 9:05 pm

Re: How has Tried EZE DOPE

Postby Wildpig » Fri Jul 12, 2013 12:10 pm

I have not used EZE dope but, here is a link to video of someone covering a Guillow Skyraider using that product.
http://www.youtube.com/watch?v=I3SCSrhYrhw
Wildpig
 
Posts: 529
Joined: Thu Jan 26, 2012 9:41 am

Re: How has Tried EZE DOPE

Postby jonathanmanopla » Fri Jul 12, 2013 12:23 pm

Wildpig wrote:I have not used EZE dope but, here is a link to video of someone covering a Guillow Skyraider using that product.
http://www.youtube.com/watch?v=I3SCSrhYrhw



thanks alredy saw the video

i want someone that use alredy , because on the Video its not look very well
jonathanmanopla
 
Posts: 23
Joined: Fri Feb 08, 2013 9:05 pm

Re: How has Tried EZE DOPE

Postby paul » Fri Jul 12, 2013 1:01 pm

I have used EZE Dope once, and it gave the tissue a mottled effect. So I went back to "normal" dope and thinners.
I am not blaming the product totally for the mottled effect, as there are more underlining reasons why this happened.
If I where to use it again I would certainly try it on a test piece first :)
paul
 
Posts: 108
Joined: Thu Aug 23, 2012 5:29 am
Location: Cleveland UK

Re: How has Tried EZE DOPE

Postby limey » Fri Jul 12, 2013 1:54 pm

Hi Jonathan I have used easydope but it was from a source in the UK . It was my first build for 40 years so I have tried lots of new materials.I found it easy to use and did get reasonable results but as the other guys have said try it on a test piece first hardly any odour so it is female frendly!!!!!!you can see my build on FIRST BUILD FOR 40YEARS. Good luck Lime.
limey
 
Posts: 36
Joined: Mon Aug 06, 2012 7:51 am

Re: How has Tried EZE DOPE

Postby Tabitha64 » Fri Jul 12, 2013 6:46 pm

I have found that if you use glue stick (I prefer purple that drys clear) to place tissue in place, then spray with water or rubbing alcohol. Allow to dry. Then apply Eze dope. I got the result I was looking for. Good luck. Tabitha
Tabitha64
 
Posts: 33
Joined: Sun May 20, 2012 9:59 am

Re: How has Tried EZE DOPE

Postby jonathanmanopla » Sat Jul 13, 2013 10:04 pm

i Let you the Picture of my Guillows Arrow just Finished , tomorrow test Flight

i Use Esaki Tissue
and Uhu Stick
after i sprayed with water and for finish use KRYLON LACQUER CLEAR
HOPE IT FLY WELL

Image
Image
Image
Image
jonathanmanopla
 
Posts: 23
Joined: Fri Feb 08, 2013 9:05 pm

Re: How has Tried EZE DOPE

Postby Wildpig » Sat Jul 13, 2013 11:25 pm

Nice looking airplane model you have! :)

Should fly very nicely.

Be sure to make test glides and adjust the tail surfaces to trim the model.
Here is something that might help:
viewtopic.php?f=2&t=2614&hilit=trimming

Also, you could search this forum for topics on trimming.
Wildpig
 
Posts: 529
Joined: Thu Jan 26, 2012 9:41 am

Re: How has Tried EZE DOPE

Postby jonathanmanopla » Mon Jul 15, 2013 11:20 am

Wildpig wrote:Nice looking airplane model you have! :)

Should fly very nicely.

Be sure to make test glides and adjust the tail surfaces to trim the model.
Here is something that might help:
viewtopic.php?f=2&t=2614&hilit=trimming

Also, you could search this forum for topics on trimming.



THANKS I FLY IT YESTERDAY ITS FLY VERY WELL AND STRAIGHT
jonathanmanopla
 
Posts: 23
Joined: Fri Feb 08, 2013 9:05 pm

Re: Guillows Arrow Finished

Postby zoltron55 » Sat Jul 27, 2013 6:36 pm

I put a little right turn on my stuff, then it doesn't get too far away
zoltron55
 
Posts: 7
Joined: Sat Jul 21, 2012 11:13 am

Re: Guillows Arrow Finished

Postby jonathanmanopla » Mon Sep 23, 2013 8:14 am

Yesterday Converted my Arrow to RC

heres the Pictures
hope to fly it on thursday i see hows goin

i Use the Electronic of a Eflite 4site

Image
Image
Image
Image
Image
jonathanmanopla
 
Posts: 23
Joined: Fri Feb 08, 2013 9:05 pm


Return to General Building Questions

Who is online

Users browsing this forum: No registered users and 26 guests