How to cover a Spitfire

Ask other modelers for a little help / knowledge ?

Postby ADW 123 » Mon Jun 20, 2011 11:45 am

dude. try using some dope on your planes. you wont turn back.
ADW 123
 
Posts: 1158
Joined: Mon Feb 22, 2010 5:22 pm
Location: Cincinnati, Ohio

Postby Phugoid » Tue Jun 21, 2011 1:49 pm

What are you using to seal the tissue then? You are sealing the tissue right?

The dope I use us called Banana oil which is a non shrinking dope which is very thin and light, and suprisingly smells of pear drops!

Andrew
Phugoid
 
Posts: 952
Joined: Wed Jan 20, 2010 8:17 am

Postby Supercubber95 » Tue Jun 21, 2011 1:53 pm

Nope. Never sealed the stuff-didn't know I had to. Where can I get banana oil? If it's non-shrinking, do I shrink the tissue with water first, then cover it in banana oil?
Who put an "S" in lisp? :P
Supercubber95
 
Posts: 218
Joined: Wed Apr 21, 2010 2:13 pm
Location: Belle Fourche, South Dakota

Postby ADW 123 » Tue Jun 21, 2011 2:18 pm

i have both shrinking and nonshrinking dopes. i use the shrinking for the larger aircraft for static display. if i am building a smaller one to fly, i use bannana oil because it wont shrink and warp my frames.

you dont have to seal. it just looks a lot better. it also will help protect the tissue from moisture that will make the tissue sag. you build you aircraft normally, shrink with water. i usually dope all of my tissue covered frames before asembly, but i have also doped them after asembly. use a quarter inch wide brush. you get the dope and the thinnner. dont use it full strength. dont ask why, because i dont have an answer.

the first coat will seem to seep right into the tisssue. be sure to wait 30 minutes at least before messing with it. do a light sand with fine grade sandpaper. this will help scratch up the surface a little for the next coat and also take off some fuzz leftover.

i use 2 coats of the stuff thinned 50/50 for flying models, and 3 coats for display.
ADW 123
 
Posts: 1158
Joined: Mon Feb 22, 2010 5:22 pm
Location: Cincinnati, Ohio

Postby Phugoid » Tue Jun 21, 2011 2:50 pm

I could not have said better myself, but I don't bother with the sanding bit in between....

You always shrink the tissue with water (or alcohol/water mix for a gentle shrink) irrespective of the dope used....
Phugoid
 
Posts: 952
Joined: Wed Jan 20, 2010 8:17 am

Postby Supercubber95 » Tue Jun 21, 2011 3:04 pm

Thanks!
Who put an "S" in lisp? :P
Supercubber95
 
Posts: 218
Joined: Wed Apr 21, 2010 2:13 pm
Location: Belle Fourche, South Dakota

Postby ADW 123 » Tue Jun 21, 2011 7:08 pm

Phugoid, i also rarely do the sanding but for my display models i want to make it look as pretty as posible and sanding it just makes me feel im doing it right. well, probably makes no difference but..
ADW 123
 
Posts: 1158
Joined: Mon Feb 22, 2010 5:22 pm
Location: Cincinnati, Ohio

Postby sawingman » Wed Jun 22, 2011 9:44 am

I have seen references to banana oil in other posts. If an LHS is not in the picture, what are other sources? From reading ADW's post I assume banana oil is classified as a non-shrinking dope! Is the banana oil used in lieu of the white glue/water mixture as a sealer?
sawingman
 
Posts: 53
Joined: Mon Apr 11, 2011 8:39 am
Location: Fullerton, CA, USA

Postby Phugoid » Wed Jun 22, 2011 2:23 pm

Yes it is a non shrinking dope (as against plain cellulose dope), it is used as a sealer for the tissue.

It's been around since Adam was a lad, so in fact it's the other way around; the white glue and water mix is used in lieu of Banana oil. This is mainly due to the white glue being a lot more friendly to the environment and kinder on the nose! I always use it with the winow wide open!

ADW knows the sources in the USA, I can get it in my LHS in England, but I'm lucky in that respect....
Phugoid
 
Posts: 952
Joined: Wed Jan 20, 2010 8:17 am

Postby scigs30 » Wed Jun 22, 2011 6:04 pm

I used to use Banana oil years ago, but have not been able to find it in recent years except for over in the UK.
scigs30
 
Posts: 844
Joined: Mon Nov 06, 2006 11:31 am

Postby sawingman » Wed Jun 22, 2011 7:18 pm

Thanks both for the feedback. Scigs, if Banana oil is basically no longer available on our side of the pond, do you use regular dope, like “Midwest Aero Gloss”. If so, do you have an online supplier?
sawingman
 
Posts: 53
Joined: Mon Apr 11, 2011 8:39 am
Location: Fullerton, CA, USA

Postby scigs30 » Wed Jun 22, 2011 8:49 pm

Brodak is sold by Dare Hobbies, they have Nitrate and Butyrate. Most people use Nitrate since it does not keep shrinking over time. Personally I use what is accessible at the LHS and that is normally Aerogloss Butyrate Dope.
scigs30
 
Posts: 844
Joined: Mon Nov 06, 2006 11:31 am

Postby Supercubber95 » Wed Jun 22, 2011 8:55 pm

Can I coat the entire model in 50/50 glue/water mix? Does it coat it sorta like dope? Or is there not any advantages to doing that?
Who put an "S" in lisp? :P
Supercubber95
 
Posts: 218
Joined: Wed Apr 21, 2010 2:13 pm
Location: Belle Fourche, South Dakota

Previous

Return to General Building Questions

Who is online

Users browsing this forum: No registered users and 33 guests