Guillows sheetwood flying models - the Zip nocals.

Ask other modelers for a little help / knowledge ?

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Fri May 05, 2017 10:58 pm

Tempo_II-GuZIP.JPG[/attachment]A photo of the prototype Tempo II, taken in 1961. The A-26 fuselage was longer and deeper for more capacity and to allow passengers to stand and walk erect inside the fuselage. Wing tip fuel tanks were added to increase flight range.

Tempo_II-GuZIP.JPG


Tempo_II_Jntr.JPG
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Sun May 07, 2017 4:17 pm

The 2-view of the Super-26 was edited in MSpaint to form this image.

SC_Sup-26_ptrn.JPG


This pattern was printed to a piece legal sized card stock and to a legal sheet of paper. The card stock copy is cut up to make patterns for cutting balsa and the paper copy will be marked up as we decide how we will build the model.

Sup-26_bld_01.JPG
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Sun May 07, 2017 4:31 pm

The card patterns are traced onto balsa sheet (1/16 for the fuse, doublers, wing, and 1/32 for the tail surfaces). The balsa parts are cut and now we have a ZIP kit for the Super-26.

Sup-26_bld_02.JPG
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Wed May 10, 2017 9:12 pm

Horizontal tail dihedral is formed. Vertical tail is attached to fuselage. The fuselage is cut into two pieces.

Sup-26_bld_03.JPG


Wing dihedral is formed. One of the nose doublers is glued to the fuselage.

Sup-26_bld_4.JPG


The other doubler is glued to the forward fuselage. Wing mounting slots are cut in the rear fuselage and nose.

Sup-26_bld_05.JPG
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Sun May 21, 2017 4:49 pm

The tail section is slid into the the 3-piece sandwich forming the nose section. This captures the wing securely to the fuselage and allows moving the wing fore and aft for minor trimming.

Sup-26_bld_06.JPG


A platform is made at the tail for mounting the horizontal tail.

Sup-26_bld_07.JPG


The Super-26 ZIP model is ready for a test flight.

Sup-26_bld_08.JPG
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Sun May 21, 2017 5:08 pm

Test flight of the Super-26 went well, which is typical of these simple ZIP gliders.

Al

Sup-26_bld_09.JPG
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Previous

Return to General Building Questions

Who is online

Users browsing this forum: No registered users and 32 guests