Guillows sheetwood flying models - the Zip nocals.

Ask other modelers for a little help / knowledge ?

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Tue Jul 21, 2015 10:45 pm

The fuselage profile and vertical tail are cut out and glued to card and traced to another sheet to draw a simple construction plan. The wing and horizontal are simpler shapes so their dimensions are simply measured on a ruler and transferred to the plan.

SC_06-21-15_LTV450_b_Sm.JPG


From the patterns and measurements, this working plan was drawn.

LTV_450_SC_plan_Sm.JPG


The plan is used for the construction of the model. A shortcut is used in the construction of the tail surfaces. The plan is slid under plastic film attached to the building board. When constructing a tail surface a piece of tissue is placed over the surface outline. Tissue is translucent enough to see the shape under it, so the sticks are glued together and to the tissue. When dry the surface is taken off the board and is ready for painting.

SC_06-21-15_LTV450_a2_Sm.JPG
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Tue Jul 21, 2015 11:09 pm

The wing panels are joined together and dihedral is formed. Wing will be removable and spans 24 inches.

SC_06-23-15_V450_1sm.JPG


The wing is fitted to the fuselage and ready for covering and painting. The chord of this narrow wing is mostly less than 2 inches. The ribs are single curved strips of balsa. We read somewhere that slow speed wings of under 2 inches chord are not critical to airfoil shape and behave very much as flat or curved plates. Our experience with small narrow wings has been the same. So our tissue covered wings of this size are not covered with tissue, just a smooth cover on top and an overall light sanding to see that the wing is smooth overall.

SC_06-23-15_V450_2sm.JPG
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Fri Jul 24, 2015 3:46 pm

After a couple of coats of thinned Elmer's white glue the model is ready for some test flights.

SC-07-22-15b.JPG


A view of the bottom of the model showing the uncovered lower surface of the wing and also shows how the removable wing works. The pointed slotted rear fuselage stick slips into a pocket formed by the three layers of the forward fuselage capturing the wing in a slot formed in the fuselage. The slot is a little longer than the wing chord allowing the wing to be moved backward or forward for minor adjustments in flight trim.

SC_07-22-15c.JPG
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Tue Aug 25, 2015 9:58 pm

OK, here's another quickie 'ZIP' no-cal swinger. The simple lines of the FJ-1 have looked like to me that it should make a quick and easy swinger.

FJ-1t_07-18-15.JPG


We found this simple 3-view by Joseph Wherry that could easily edited into a image to use for making cutting patterns.

Wherrey_3vu-sm.JPG


After a bit of work on it in MS paint we came up with this.

Whry_ptrn_sm.JPG
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Tue Aug 25, 2015 10:17 pm

First the image is printed to a sheet of cardstock.

SC-07-16-15-aSm.JPG


The sheet us cut up to make patterns for cutting balsa. Note a small correction(the red line at the vertical tail shows a different shape of the bottom of the vertical tail and notch cut into the rear fuselage to accept it).

SC_07-16-15-bSm.JPG


Using the patterns, a couple of sharp blades and a metal straight edge, a bit is balsa is transformed into a 'ZIP' kit of the FJ-1.

SC_07-20-15_fury-sm.JPG
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Tue Aug 25, 2015 10:40 pm

The FJ-1 builds up quickly. First the vertical tail is glued t the fuselage and dihedral is formed in the wing and horizontal tail.

SC_07-21-15_aSm.JPG


Next the nose doublers are glued in place and the wing and horizontal stab are attached.

SC_08-04-15a.JPG


To complete the model for flight, some lead BBs are inserted in holes drilled in the nose and a small loop of tread is glued to the left wing tip. The wing span of the FJ-1 is eleven inches.
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Tue Aug 25, 2015 10:45 pm

Test flights on a short line go OK.

SC_08-04-15b1.jpg


SC_08-04-15b2.jpg


SC_08-04-15b4.jpg
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Thu Nov 26, 2015 12:05 am

Our latest ZIP nocal is this P-51 of about 14 inches wingspan.
P-51_11-24-15b.JPG

There's a kinda long road from which this model comes from. Back in about 1953 we were trying to learn to fly U-control. One of our learning crashes was profile P-51 designed by Walter Musciano for 1/2 A power. For a nostalgic experience we decided to shrink the P-51 and build and fly it as a swinger. We found a plan for the Musciano P-51 in one of his first books in a library. The shapes of the P-51 we captured to a jpg file like this.
P-51_pattern.JPG

The JPG was printed to a letter size sheet of cardstock and cut up for patterns to be used for cutting balsa.
SC_11-12-15aSm.JPG
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Thu Nov 26, 2015 12:45 am

Using the card patterns as a guide the parts are cut from sheet balsa. The fuse and wing are 1/16 balsa and the coublers and tail parts are 1/32. At this point we have parts for a ZIP kit.
SC-11-13-15a.JPG

Fuselage and wing coming together.
SC_11-13-15b.JPG

To simulate the engine for the model P-51, the cylinder and crankcase of a run-out Cox Pee Wee is used as a nose weight.
SC_11-14-15b.JPG
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Thu Nov 26, 2015 9:31 pm

Test fit of the Mustang parts and some decoration is added.
SC_11-15-15a.JPG

We are attempting a simple replication in model form of the Mustang in the attached pic. N2251D was used by Bob Hoover in the 1960s. It was replaced in 1972 by another Mustang N51RH.

We attended a Confederate Air Force Air Show in Harlingen, TX in 1976 and had the opportunity to see Bob Hoover fly the Shrike Commander and the P-51. Both were amazing flights by a man who knew his aircraft thoroughly and could fly them to the edge of their flight envelope. They are experiences that I treasure to this day.
RH_mustang_one.JPG

Final assembly of the P-51 of the parts and construction of foam wheels for the craft.
SC_11-20-15a.JPG
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Thu Nov 26, 2015 9:43 pm

P-51 assembled and ready for test flights.
SC_11-21-15b.JPG

SC_11-21-15c.JPG

In test flights the little Mustang flys very fast with the right wing in a severe low right wing position.
SC_11-21-15d.jpg
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Thu Nov 26, 2015 10:04 pm

This brings the Mustang to the first picture of it posted above. To try to improve its flight characteristics, we decided to lighten the model and increase the wing dihedral. First the landing gear is removed the Pee Wee is replaced with a Telco Shark.
P-51_11-24-15a.JPG

A quick test flight showed some decrease in flight speed.
P-51_fly_11-24-15.JPG

Now for a increase in dihedral.
P-51_11-25-15.JPG
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Mon Apr 24, 2017 12:20 pm

We were doing a google search on the OnMark Marksman N256H and found the attached pic, in curiosity we clicked on it to see where it was and found the Guillows forum and learned it was from a post a year and a half ago, so we decided to bump the thread forward a bit.

Al
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Mon Apr 24, 2017 12:35 pm

A quick update on the A-26 project is a profile ZiP swing control model of the L.B. Smith Sup-26 illustrated below. Since it is model we will make it a 'what if' model - supposing if Mr Smith had decided to build a single engine version of the Super-26.

Al
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

Re: Guillows sheetwood flying models - the Zip nocals.

Postby simpleflyer » Fri May 05, 2017 10:00 pm

The above sketch was edited from the sketch attached below. The sketch and a two view drawing are from an article about the Super-26 conversion of the Douglas A-26 by LB Smith. The Super-26 next evolved into the Tempo II conversion of the A-26. IMHO, one of the finest and best looking conversions of the A-26

Sup-26_dwg.JPG


Sup-26_3view.JPG


al
You do not have the required permissions to view the files attached to this post.
simpleflyer
 
Posts: 476
Joined: Wed Apr 25, 2007 12:51 pm
Location: Rosenberg, Texas

PreviousNext

Return to General Building Questions

Who is online

Users browsing this forum: No registered users and 24 guests